The media access control method of all Ethernet networks is |
CSMA/CD |
A network is connected following the IEEE 802.3 specifications. Which of the following best describes when a device can transmit messages? |
The device listens to determine if the transmission media is free. |
Which of the following use the CSMA/CD access method?(2 answers) |
10BaseT 1000BaseT |
Which of the following physical topologies are used with Ethernet networks?(2 answers) |
Star Bus |
Ethernet 100BaseFX networks use what type of cabling? |
Fiber-optic |
Which of the following Ethernet standards uses fiber optic cabling?(2 answers) |
100BaseFX 1000BaseLX |
Your network follows the 100BaseTx specifications for Fast Ethernet. What is the maximum cable segment length allowed? |
100 meters |
With an Ethernet 10BaseT network, the maximum cable length between a computer and the hub is: |
100 meters |
You have been tasked with designing an Ethernet network. Your client needs to implement a very high-speed network backbone between campus buildings; some of which are around 300 m apart. Fiber-optic cabling has already been installed between buildings. Your client has asked that you use the existing cabling that operates at full-duplex. Which Ethernet standard meets these guidelines?(2 answers) |
10GBaseSR 1000BaseSX |
What type of cabling is used with 100BaseTX Fast Ethernet networks? |
Type 1A STP or Category 5 UTP |
What topology is used with 100BaseTX Fast Ethernet networks?(2 answers) |
Physical star/logical bus Physical star/logical star |
Which of the following are requirements of the 1000BaseT Ethernet standards?(3 answers) |
RJ-45 connectors The cable length must be less than or equal to 100m CAT 5e cabling |
You are planning a network for an educational campus. Due to the size of the buildings and the distance between them, you have elected to use 10BaseFL hubs, cabling, and network interface cards. What is the maximum length for the network cable between a workstation and a hub? |
2000 meters |
Which Gigabit Ethernet standard uses multimode fiber-optic cabling and supports network segments up to a maximum of 550 m long? |
1000BaseSX |
You have been tasked with designing a high-speed Ethernet network. Your client's building already has 150 ohm shielded twisted pair wiring installed. Due to budget constraints, they have asked you to reuse the existing wiring instead of installing new fiber optic cabling. Which Ethernet standard could you implement in this situation? |
1000BaseCX |
You would like to implement 10 Gbps Ethernet over a distance of 1 km or greater. Which of the following would be the minimum requirement for the implementation?(2 answers) |
10GBaseLR standards Single mode fiber |
Which of the following standards is used by SONET? |
10GBaseLW |
You want to implement an Ethernet network at very long distances using fiber optic cables. Which standard and cable type would you choose?(2 answers) |
Single Mode Fiber 1000BaseLX |
You need to transfer data from one laptop to another and would like to use an Ethernet cable. You do not have a hub or a switch. |
Crossover |
You want to connect the LAN port on a router to the uplink port on a switch. The switch does not support auto-MDI. |
Crossover |
You have two switches that you need to connect using their uplink ports. The switches do not support auto-MDI. |
Crossover |
You need to connect a workstation to a switch using a regular port on the switch (not an uplink port). The switch does not sport auto-MDI. |
Straight-Through |
You have purchased a new router that you need to configure. You need to connect a workstation to the router's console port to complete the configuration task. |
Rollover |
Which of the following connectors is typically used on one end of a rollover cable? |
serial |
Using the exhibit to match the connector type on the left with the corresponding letter on the right. |
A- DB-25 B- DB-9 C- RJ45 D- RJ11 E- LC F- BNC G- F-Type |
You want to create a rollover cable that has an RJ-45 connector on both ends. How should you connect the wires within the connectors? |
Connect pin 1 to pin 8, pin 2 to pin 7, pin 3 to pin 6, and pin 4 to pin 5 |
You are implementing a SOHO network for a local business. The ISP has already installed and connected a cable modem in the business. The business has four computers that need to communicate with each other and the internet. You examine each computer and notice only one of the four has a wireless NIC; they all have ethernet NICs. |
An unmanaged switch and Cat5e cabling |
You manage the two-location network shown in the exhibit. Workstations and servers at each location connect to a patch panel using behind-the-wall wiring. The patch panel.... |
Drop Cables Cat6 straight-through UTP Patch Cables Cat6 straight-through UTP Uplink Cables Cat6 crossover UTP WAN Cable Single-mode fiber optic |
Which of the following tests can be performed by a TDR? |
Measure the length of a cable. Identify the location of a fault on a cable. |
You have a network connected using a physical bus topology. One of the cables connecting a workstation to the bus breaks. |
No device is able to communicate. |
You manage a network that uses 1000BaseT Ethernet. You find that one device communicates on the network at only 100 Mbps. |
Certifier |
You are creating an Ethernet network for your company. The shipping department is located in a different building that is located 150 meters from the main wiring closet. You connect a single Cat 6e cable to connect the wiring closet to the shipping building. |
Repeater |
A user from the Sales department calls to report that he is experiencing problems connecting to the Sales file server. All users in the Sales department connect to the Sales server through a single Ethernet switch. No other users have reported problems connecting to the Sales server. |
Replace the network card in the user's computer. |
Users report that the Internet is no longer accessible. You suspect that the line connecting your building to the Internet is not working properly. |
Smart jack. |
You are troubleshooting a client connectivity problem on an Ethernet network. The client system has intermittent connectivity to the network. You discover that the UTP patch cable is run 75 feet from the wall outlet, passes through the ceiling and over several florescent light fixtures before reaching the client system. |
EMI interfaace. |
You are moving a client to a new location within an Ethernet network. Previous to the move, the client system did not have any difficulty accessing the network. |
Failed patch cable between the client system and the wall jack. |
You are creating an Ethernet network for your company. The shipping department is located in a different building that is located 150 meters from the main wiring closet. You connect a single Cat6e cable to connect the wiring closet to the shipping building. |
Attenuation. |
You have decided to implement Gigabit Ethernet on your network. Each switch port is connected to a single device. Following the installation, you find one device connected to a switch that is only running at 100 Mbps. |
Crosstalk. |
You have a cable Internet connection at home. The installer had connected the router near the outside wall of your house with RG-6 cable. |
Echo |
You want to measure the voltage, amps, and ohms of various devices. |
Multimeter. |
Which of the following standards is typically used in a rollover cable? |
RJ-232 |