CCNA 2 Chapter 6 Exam

Your page rank:

Total word count: 812
Pages: 3

Calculate the Price

- -
275 words
Looking for Expert Opinion?
Let us have a look at your work and suggest how to improve it!
Get a Consultant

What are three primary benefits of using VLANs? (Choose three.)

Security Cost Reduction improved IT staff efficiency

Which type of VLAN is used to designate which traffic is untagged when crossing a trunk port?


A network administrator is determining the best placement of VLAN trunk links. Which two types of point-to-point connections utilize VLAN trunking?​ (Choose two.)

Between two switches that utilize multiple Vlans Between a switch and a server that has an 802.1Q NIC

What must the network administrator do to remove Fast Ethernet port fa0/1 from VLAN 2 and assign it to VLAN 3?

Enter the switchport access vlan 3 command in interface configuration mode

When a Cisco switch receives untagged frames on a 802.1Q trunk port, which VLAN ID is the traffic switched to by default?

native VLAN ID

Port Fa0/11 on a switch is assigned to VLAN 30. If the command no switchport access vlan 30 is entered on the Fa0/11 interface, what will happen?

Port Fa0/11 will be returned to VLAN 1

Which command is used to remove only VLAN 20 from a switch?

no vlan 20

What happens to a port that is associated with VLAN 10 when the administrator deletes VLAN 10 from the switch?

The port becomes inactive

Which two characteristics match extended range VLANs? (Choose two.)

VLAN ID’s exist between 1006 to 4094 They are saved in the running-config file by default

A Cisco switch currently allows traffic tagged with VLANs 10 and 20 across trunk port Fa0/5. What is the effect of issuing a switchport trunk allowed vlan 30 command on Fa0/5?

It allows only VLAN 30 on Fa0/5

Refer to the exhibit. PC-A and PC-B are both in VLAN 60. PC-A is unable to communicate with PC-B. What is the problem?

The Vlan that is used by PC-A is not in the list of allowed VLANs on the trunk

Refer to the exhibit. DLS1 is connected to another switch, DLS2, via a trunk link. A host that is connected to DLS1 is not able to communicate to a host that is connected to DLS2, even though they are both in VLAN 99. Which command should be added to Fa0/1 on DLS1 to correct the problem?

switchport trunk native vlan 66

What is a characteristic of legacy inter-VLAN routing?

The router requires one Ethernet link for each VLAN

Which four steps are needed to configure a voice VLAN on a switch port? (Choose four).

Configure the switch port in access mode Add a voice VLAN Assign the voice VLAN to the switch port Ensure the voice traffic is trusted and tagged with CoS priority value

What is a disadvantage of using router-on-a-stick inter-VLAN routing?

does not scale well beyond 50 VLANs

Refer to the exhibit. Router RA receives a packet with a source address of and a destination address of What will the router do with this packet?

The router will forward the packet out interface FastEthernet 0/1.2

Refer to the exhibit. In what switch mode should port G0/1 be assigned if Cisco best practices are being used?


A small college uses VLAN 10 for the classroom network and VLAN 20 for the office network. What is needed to enable communication between these two VLANs while using legacy inter-VLAN routing?

A router with at least two LAN interfaces should be used

Refer to the exhibit. A network administrator needs to configure router-on-a-stick for the networks that are shown. How many subinterfaces will have to be created on the router if each VLAN that is shown is to be routed and each VLAN has its own subinterface?


When configuring a router as part of a router-on-a-stick inter-VLAN routing topology, where should the IP address be assigned?

to the subinterface

A high school uses VLAN15 for the laboratory network and VLAN30 for the faculty network. What is required to enable communication between these two VLANs while using the router-on-a-stick approach?

A switch with a port that is configured as a trunk is needed when connection to the router

Refer to the exhibit. A router-on-a-stick configuration was implemented for VLANs 15, 30, and 45, according to the show running-config command output. PCs on VLAN 45 that are using the /24 network are having trouble connecting to PCs on VLAN 30 in the /24 network. Which error is most likely causing this problem?​

There is an incorrect IP address configured on GigabitEthernet 0/0.30

Match the IEEE 802.1Q standard VLAN tag field with the descriptions. (Not all options are used.)

User Priority -> value that supports level or service implementation Type -> value for the tag protocol ID value Canonical Format Identifier -> an identifier that enables Token Ring frames to be carried across Ethernet Links – not scored – -value for the application protocol of the user data in a frame VLAN ID -> VLAN number

The __________ Command displays the VLAN assignment for all the ports as well as the existing VLANs on the switch

show vlan

Which PCs will receive the broadcast sent by PC-C? (packet tracer question)


Share This

More flashcards like this

NCLEX 10000 Integumentary Disorders

When assessing a client with partial-thickness burns over 60% of the body, which finding should the nurse report immediately? a) ...

Read more


A client with amyotrophic lateral sclerosis (ALS) tells the nurse, "Sometimes I feel so frustrated. I can’t do anything without ...

Read more

NASM Flashcards

Which of the following is the process of getting oxygen from the environment to the tissues of the body? Diffusion ...

Read more

Unfinished tasks keep piling up?

Let us complete them for you. Quickly and professionally.

Check Price

Successful message