4.3.4 Practice Questions

You need to transfer data from one laptop to another and would like to use an Ethernet cable. You do not have a hub or a switch. Which type of cable should you use?

Crossover

You want the LAN port on a router to the uplink port on a switch. The switch does not support auto-MDI. Which type of cable should you use?

Crossover

You have two switches that you need to connect using their uplink ports. The switches do not support auto-MDI. which type of cable should you use?

Crossover

You need to connect a workstation to a switch using a regular port on the switch (not an uplink port). The switch does not support auto-MDI. Which type of cable should you use?

Straight-through

You have purchased a new router that you need to configure. You need to connect a workstation to the router's console port to complete the configuration tasks. Which type of cable would you most likely use?

Rollover

Which of the following connectors is typically used on one end of the rollover cable?

Serial

Which of the following standards is typically used in a rollover cable?

RS-232

Use the exhibit to match the connector type on the corresponding letter on the right.

A=DB-25 B=DB-9 C=RJ45 D=RJ11 E=LC F=BNC G=F-Type

You want to create a rollover cable that has an RJ-45 connector on both ends. How should you connect the wires within the connectors?

Connect pin 1 to pin 8, pin 2 to pin 7, pin 3 to pin 6, and pin 4 to pin 5

You are implementing a SOHO network for a local business. The ISP has already installed and connected a cable modem in the business. The business has four computers that need to communicate with each other and the internet. The ISP's cable modem has only one RJ45 port. You need to set up the network with the following in mind: Spend as little money as possible, do not purchase unnecessary equipment, computers need to have a gigabit connection to the network, and new devices should not require management or configuration. You examine each computer and notice only one of the four computers has a wireless NIC; they all have Ethernet NICs. What should you purchase?

An unmanaged switch and CAT5e cabling

You manage the two-location network shown in the exhibit. Workstations and servers at each location connect to a patch panel using behind-the-wall wiring. The patch panel then connects network hosts to one of three 1000BASE-T switches. Routers are implemented at each location together using a private WAN. The switch ports have auto-MDIX disabled.

A=Cat 6 straight-through UTP B=Cat 6 straight-through UTP C=Cat 6 crossover UTP D=Single-mode fiber optic

4.3.4 Practice Questions - Subjecto.com

4.3.4 Practice Questions

Your page rank:

Total word count: 448
Pages: 2

Calculate the Price

- -
275 words
Looking for Expert Opinion?
Let us have a look at your work and suggest how to improve it!
Get a Consultant

You need to transfer data from one laptop to another and would like to use an Ethernet cable. You do not have a hub or a switch. Which type of cable should you use?

Crossover

You want the LAN port on a router to the uplink port on a switch. The switch does not support auto-MDI. Which type of cable should you use?

Crossover

You have two switches that you need to connect using their uplink ports. The switches do not support auto-MDI. which type of cable should you use?

Crossover

You need to connect a workstation to a switch using a regular port on the switch (not an uplink port). The switch does not support auto-MDI. Which type of cable should you use?

Straight-through

You have purchased a new router that you need to configure. You need to connect a workstation to the router’s console port to complete the configuration tasks. Which type of cable would you most likely use?

Rollover

Which of the following connectors is typically used on one end of the rollover cable?

Serial

Which of the following standards is typically used in a rollover cable?

RS-232

Use the exhibit to match the connector type on the corresponding letter on the right.

A=DB-25 B=DB-9 C=RJ45 D=RJ11 E=LC F=BNC G=F-Type

You want to create a rollover cable that has an RJ-45 connector on both ends. How should you connect the wires within the connectors?

Connect pin 1 to pin 8, pin 2 to pin 7, pin 3 to pin 6, and pin 4 to pin 5

You are implementing a SOHO network for a local business. The ISP has already installed and connected a cable modem in the business. The business has four computers that need to communicate with each other and the internet. The ISP’s cable modem has only one RJ45 port. You need to set up the network with the following in mind: Spend as little money as possible, do not purchase unnecessary equipment, computers need to have a gigabit connection to the network, and new devices should not require management or configuration. You examine each computer and notice only one of the four computers has a wireless NIC; they all have Ethernet NICs. What should you purchase?

An unmanaged switch and CAT5e cabling

You manage the two-location network shown in the exhibit. Workstations and servers at each location connect to a patch panel using behind-the-wall wiring. The patch panel then connects network hosts to one of three 1000BASE-T switches. Routers are implemented at each location together using a private WAN. The switch ports have auto-MDIX disabled.

A=Cat 6 straight-through UTP B=Cat 6 straight-through UTP C=Cat 6 crossover UTP D=Single-mode fiber optic

Share This
Flashcard

More flashcards like this

NCLEX 10000 Integumentary Disorders

When assessing a client with partial-thickness burns over 60% of the body, which finding should the nurse report immediately? a) ...

Read more

NCLEX 300-NEURO

A client with amyotrophic lateral sclerosis (ALS) tells the nurse, "Sometimes I feel so frustrated. I can’t do anything without ...

Read more

NASM Flashcards

Which of the following is the process of getting oxygen from the environment to the tissues of the body? Diffusion ...

Read more

Unfinished tasks keep piling up?

Let us complete them for you. Quickly and professionally.

Check Price

Successful message
sending